Peugeot 3008 Key Fob Problems
Peugeot's mid-sized 3008 SUV has lot going for it. It is well-constructed, drives nice and has a big boot. But can it fend against strong competition in the most crowded area of the market?
If your Peugeot keyfob doesn't work, it may have been exposed to clean or soapy tap water. You may need to remove the battery and clean it using electronic cleaner or isopropyl alcohol.
Dead coin battery
Peugeot key fobs have small coin batteries that powers their remote locking as well as other functions. This battery has a limited lifespan and can wear out after years of usage. Voltage testing is an easy method to determine if a battery is in a bad state. A multimeter is used to measure the voltage between the battery's plus and minus poles. The results of this test will tell you whether the battery is dead or not.
If you've been using your Peugeot 3008 for a while, and the key fobs have stopped functioning, it could be an issue with the receiver module. The receiver module is in charge of receiving radio frequency signals transmitted through key fobs and then sending them to the car's systems. If the receiver module is in an issue, it will not be able transmit commands to other modules inside the car.
Another common reason for a non-working key fob is sweat or moisture in the circuit board. This can result in short circuits that drain the battery, and also disable the remote locking feature of the key fob. If this happens, you should bring your key fob to a specialist in chip level repairs.
Water damage
Whether you dropped your key fob into the pool, threw it into the wash or even left it in the rain for too long, water damage can cause a lot of problems. Water is a good conductor, and can cut off circuit boards. It could also cause corrosion of the metal traces as well as other components on the key fob. A wet circuit can cause the battery to lose charge.
If you have an extra key fob, you can use it to lock or unlock the Peugeot 3008 in order to eliminate a dead coin-cell battery as the reason for the problem. Interference signals can also cause your key fob to stop working properly. These interfere with the signal sent by the receiver module. These interference signals can come from a wide range of sources that include radio transmitters near by.
If you hear sloshing sounds coming from your Peugeot 3008 when driving it could be due to a blocked condensate drain of the evaporator. You can test this by blowing compressed air into the drain holes under your door. You can also use flexible metal wire for wriggling drain holes to get rid of any dirt collected. Air pockets can also be detected by sloshing noises.
A malfunctioning receiver module
The receiver module inside the Peugeot 3008 key fob is responsible for transmitting the remote keyless system signal from the key fob to the car's receiver. This module could be damaged and prevent the car from recognizing your key fob. peugeot key fob could be caused by the battery being dead or water damage. or, interference from electronic devices operating at the same frequency. In these instances, the car may show the message "card not detected" on the display.
There are many options to fix this issue. You can try replacing the battery or reprogramming the key fob. You can also use a spare key to start the car. However, if your key fob isn't functioning after all these steps, it might have a chip that's faulty.
The best way to tell whether the key fob is equipped with a malfunctioning chip is to take it off and clean it up with a paper towel and rubbing alcohol. If the chip is damaged, you need to purchase an entirely new one. The FB Series enclosures come with an holder for coin cells that fits the most popular types of key fob batteries. They can also be customized by using digital printing and CNC machined cutouts. If your key fob was exposed to salty or dirty tap water, the chip could be contaminated and requires to be cleaned.
Faulty keyless entry system
If you receive the message "card not detected", it means that your car cannot receive a signal from your key fob. This could be due to several reasons, such as the battery being weak or dead. Often, the problem can be solved by pressing the start button using the key fob. In some instances however, you might need to take your key fob to a Peugeot dealership for further repairs.
The first step to resolve a Peugeot 3008 key fob that isn't able to unlock or lock the doors is to test its battery. Batteries are the primary cause of a malfunctioning fob however, there are other factors that can contribute to this issue as well. These include worn buttons, damage to the receiver module, water problems and signal interference.
If your Peugeot key fob has been exposed to pure tap water, it's a good idea to take the battery off. Then dry the electronic components using paper towel. You can also try isopropyl alcohol or an appropriate cleaner for this. If the fob has been exposed to salt or soapy water, it's best to replace it.
If your key fob still does not work You can reset it by removing the 12 volts battery for 15 minutes. Then reconnect the negative cable first, then followed by the positive cable.